User talk:Hebron
From uCtrl.net
Old messages moved to archive, click here to read.
Contents |
Question
Hi, just wonderig where did you get your awsome rackbox thing that holds all of your projects? Also where do you get your wire? it is an odd question, but places like Radio shack have bad wire selection...
Thanks
Fuse Box
Hi, I dont quite understand how the fuse box that you have works. What optocouplers are you using? Most I have found only allow around 1.5V input on pin 1, so I think that with a 5 and 12 volt power supply I would damage them. Also what are you using for the inverter? Sorry for so many questions.
Thank you.
RE: Fuse Box
Sorry, but I have a few last questions about this. Are all the other modules you have connected to the 5V and 12V power supplies? I am wondering because with the resistors wont it reduce the voltage output? Also on the schematic, you have a +5V, and -5V power supply, is the -5V the ground or is it like on a transformer where I believe you have a +5V 0V -5V so you have the option of 5V or 10V? The last two questions: From one of the images it looks like you have two 16-pin cradles and one 6-pin. Are the two 16-pin cradles the inverters and the 6-pin the opto coupler, is only one opto coupler need, or is it one inverter and two opto couplers? Lastly, what kind of transistor do I need?
Sorry about so many questions.
Thanks.
RE: RE: Fuse Box
Ohh, I see how this works. Thanks!
Need help with AVR
Hi agian, I have some parts coming in the mail so mean while I have been trying again and again to get a simple switch to work. I dont know why but it isnt working. The switch set up I am using is on one of your pages: http://uctrl.net/w/AVR#Input I am also using CodeVisionAVR. I have tried many resouces and cannot get it to work. Do you have any suggestions?
Thanks
RE: Help with AVR
Hi, the set up I am currently using which may not be the best is I am using a USB programmer from http://www.adafruit.com/index.php?main_page=product_info&cPath=16&products_id=46&zenid=a431e86b9bace9e0fe8671d2a009f0d7 and have DIY AVR cradle that plug into the breadboard. I dont know how to attach a picture of my ATTiny15/ATTiny13 and ATTiny2313 Cradles, they are really simple just header pins, a PCB, and a wire wrap cradle. The reason I went with the AVR Cradles is they were really cheap and very small. The inputs are connected directly to the pins on the AVR. I just found a few minutes ago that if I remove the 330 ohm resistor the switch does work. I have seen some schematics like this online where that resistor is removed, but I am not sure if it is good for the AVR.
-- Thebigbucks 23:09, 10 December 2009 (UTC)
Fuse Box
You have three 5v and three 12v power supplys. Do you have this because too much current is needed to run all of the modules and parts? What fuses are you using, as in how many Amps?
Thanks :D
facebook gone?
what happened to your facebook?
I was going to ask if I can host my own DNS server over the game.uctrl.net domain ;)
--1oooop 15:14, 18 March 2011 (CET)
domain name buying
I don't understand how the whole process works, could you enlighten me?
Email forwarding
Hi, I'm just wondering if email forwarding is enabled for game.uctrl.net... if not, can you please enable it? --1oooop
PS: check out the gameclub site!
re: re: Email forwarding
aww... okay...
thanks for mail forwarding
thanks for the mail forwarding --1oooop 04:26, 26 September 2011 (CEST)
DNS change
Hey Hebron, nice to see you around.
I kinda changed my address. It is now [1] can you please change my entry?
Thanks, 1oooop
